Powerint LNK417EG 15W離線LED驅動電源方案(DER284)

發布時間:2011-8-19 12:21    發布者:1770309616
關鍵詞: LED驅動電源 , LNK417EG , Powerint
Powerint公司的LinkSwitch-PH系列大大地簡化了實現功率因素大于0.9,TRIAC調光和高效率的LED驅動器的設計.器件集成了725V功率MOSFET,連續模式PWM控制器,用于自偏壓的高壓開關電流源,頻率抖動,逐個周期限流和滯后熱關斷電路,最適合用于離線LED驅動器.本文介紹了LinkSwitch-PH系列產品亮點, 功能方框圖, 14W和7W LED驅動器電路圖,以及采用LNK417EG無電解電容高效率(≥90%) PFC大于0.9的15W LED驅動器參考設計電路圖,主要指標和材料清單與PCB布局圖.

LinkSwitch-PH dramatically simplifies implementation of LED drivers requiring Power Factors greater than 0.9, TRIAC dimming, and high efficiency. This highly integrated controller introduces a new control technique that provides very high power factor and accurate output current control, and eliminates passive circuitry required for power factor correction, optocoupler and secondary current control circuitry.

Each device incorporates a 725V power MOSFET, a continuous-mode PWM controller, a high voltage switched current source for self biasing, frequency jittering, cycle-by-cycle current limit and hysteretic thermal shutdown circuitry into a monolithic IC.

LinkSwitch-PH系列產品亮點:

Dramatically Simplifies Off-line LED Drivers

Single-stage power factor correction and accurate constant current (CC) output

Flicker-free, phase-controlled TRIAC dimming

Eliminates optocoupler and all secondary current control circuitry

Eliminates all control loop compensation circuitry

Simple primary-side PWM dimming interface

Universal input voltage range

Enables designs that are electrolytic-free

Accurate and Consistent Performance

Fast start-up time

Compensates for transformer inductance tolerances

Compensates for line input voltage variations

Frequency jittering greatly reduces EMI filter size and costs

Advanced Protection and Safety Features

Auto-restart for short circuit protection

Open circuit fault detection mode

Automatic thermal shutdown or restart with hysteresis

Meets high voltage creepage requirement between DRAIN and all other signal pins both on PCB and at package

EcoSmart - Energy-Efficiency Technology

Low standby power remote ON/OFF feature (< 50 mW at 230 VAC)

No current sense resistors - maximizes efficiency

High efficiency operation, >85% achievable

Green Package

Halogen free and RoHS compliant package

LinkSwitch-PH應用:

• Off-line LED driver

圖1. LinkSwitch-PH系列功能方框圖

圖2. LinkSwitch-PH系列絕緣TRIAC調光高功率因素通用輸入14W LED驅動器電路圖

圖3. LinkSwitch-PH系列絕緣無調光高功率因素通用輸入7W LED驅動器電路圖 采用LNK417EG無電解電容高效率(≥90%) PFC大于0.9的15W LED驅動器參考設計

This document describes an isolated, power factor corrected, very high efficiency LED driver designed to drive a 30 V LED string at a current of 500 mA (nominal). The input voltage range is 90 VAC to 265 VAC.

The LED driver uses a LNK417EG device from the LinkSwitch-PH family of ICs. This integrated controller and 725 V MOSFET dramatically reduces the complexity and component count of the solution.

The key design goals were to achieve the highest possible efficiency and eliminate electrolytic capacitors. Both are key factors for increasing the lifetime and reliability of LED drivers making this solution ideal for industrial and commercial applications.

15W LED驅動器參考設計主要特性:

No electrolytic capacitors

Clean monotonic start-up – no output blinking

Fast start-up (<100 ms) – no perceptible delay

Highly energy efficient

o ≥90% at 115 VAC and 230 VAC input Low cost, low component count and small printed circuit board footprint solution

o No current sensing required

o Frequency jitter for smaller, lower cost EMI filter components Integrated protection and reliability features

o Output open-circuit / output short-circuit protected with auto-recovery

o Line input overvoltage shutdown extends voltage withstand during line faults.

o Auto-recovering thermal shutdown with large hysteresis protects both components and printed circuit board

o No damage during brown-out or brown-in conditions

Meets IEC 61000-4-5 ring wave, IEC 61000-3-2 Class C harmonics and EN55015 B conducted EMI


圖4.15W LED驅動器參考設計外形圖: 3.115” L x 1.525” W.
電源指標:


圖5.15W LED驅動器參考設計電路圖


圖6.變壓器電路圖
變壓器主要指標:



圖7. PCB布局圖(頂層)
詳情請見:
http://www.powerint.com/sites/default/files/product-docs/linkswitch-ph_family_datasheet.pdf

http://www.powerint.com/sites/default/files/PDFFiles/der284.pdf
本文地址:http://selenalain.com/thread-73734-1-1.html     【打印本頁】

本站部分文章為轉載或網友發布,目的在于傳遞和分享信息,并不代表本網贊同其觀點和對其真實性負責;文章版權歸原作者及原出處所有,如涉及作品內容、版權和其它問題,我們將根據著作權人的要求,第一時間更正或刪除。
您需要登錄后才可以發表評論 登錄 | 立即注冊

關于我們  -  服務條款  -  使用指南  -  站點地圖  -  友情鏈接  -  聯系我們
電子工程網 © 版權所有   京ICP備16069177號 | 京公網安備11010502021702
快速回復 返回頂部 返回列表
午夜高清国产拍精品福利|亚洲色精品88色婷婷七月丁香|91久久精品无码一区|99久久国语露脸精品|动漫卡通亚洲综合专区48页